高低溫試驗箱常見問題不升溫、不恒溫應如何解決?
高低溫試驗箱的最高溫度一般是到150℃,最低溫度一般是到-70℃,主要是通過鎳鉻合金電加熱產生高溫,如果試驗箱不升溫時,應先將機器總電源關掉,檢查加熱斷路器是否有跳閘,如果有則合上,如沒有,則繼續往下查,首先用萬用表的電阻檔,測量固態繼電器的輸出端(2腳)到N線之間是否有約20歐的電阻(視不同的機型稍有變化),如果沒有,則說明加熱絲開路了,重點檢查加熱絲是否損壞;如果加熱絲沒有損壞,則打開配電箱側蓋將機器運轉并處于升溫狀態,觀察固態繼電器上的導通指示燈是否點亮,如果有點亮,則用萬用表的電壓檔,測量固態繼電器的輸出端(1腳)對N線是否有220V電壓,如果沒有,再往上查接觸器,如果有,再測量固態繼電器的輸出端(2腳)對N線是否有220V電壓,如果沒有,則說明固態繼電器內部開路損壞,須更換。
高低溫試驗箱不恒溫、波動大解決方法:
1、調整參數,設備定值運行時實時溫度接近設定溫度時,點擊運行畫面“AT鍵,自整定P.I.D,請耐心等待,待屏幕右上角“AT”不顯爍時,表示己自整定完畢;
2、傳感器或控制器的ACU模塊有損壞或不良,造成溫度不穩及波動;
3、檢查循環馬達運轉是否正常,風輪是否有卡住,導致風帶時快時慢;
4.、試驗箱內試驗品堆放得太多(正常情況下不超過內箱總容積的三分之一),導致風無法循環,溫度波動大。